Can Jon Boat Outriggers Be Used In Saltwater? A Simple Guide
Have you ever taken your jon boat into salt water and felt it tip? I have. It is not fun. The good news is that outriggers can help. Can jon boat outriggers be used in saltwater? Yes, they can. But you need the right kind. You also need to take care of them. This guide will show you how. We will talk about materials, installation, and care. You will learn what works and what does not. Let us get started.
Can Jon Boat Outriggers Be Used In Saltwater?
Yes, you can use outriggers on a jon boat in salt water. I have done it many times. They add stability. They stop the boat from rolling. This is great when you fish or crab. But salt water is hard on gear. It eats metal fast. You must pick the right outriggers. Aluminum ones can corrode. Stainless steel lasts longer. Plastic or PVC works too. The floats must handle salt and sun. Foam-filled floats are best. They do not sink if cracked. Always rinse gear after each trip. Salt kills metal fast.
I learned this the hard way. My first set rusted in one season. Now I use marine-grade parts. I coat bolts with grease. I store them dry. They last years now. Do you want gear that lasts? Pick saltwater-rated parts. It saves money long term.
Outriggers also help in chop. They widen your stance. The boat feels solid. You can stand and cast. You can pull heavy traps. But they add drag. Your motor works harder. Fuel use goes up. Plan for this. A bigger prop may help. Or trim the motor up.
Some folks think outriggers look odd. I say function beats looks. A stable boat is a safe boat. Kids and dogs move less. Gear stays put. You fish more. You worry less. That is a win.
Check your local laws too. Some states limit width. Outriggers count in width. Measure before you buy. Fines are no fun. Know the rules.
Mounting matters. Weak mounts fail. The transom takes stress. Use backing plates. Bolt through thick wood. Or use a strong bracket. Do not trust screws alone. They pull out in rough water.
I use through-bolts with washers. I add marine sealant. Water stays out. The wood stays dry. Rot is the enemy. Seal every hole.
Test in calm water first. Load the boat. Walk the gunwales. Feel the stability. Adjust float height if needed. Floats should kiss the water at rest. They dig in when you lean.
Do you fish alone? Outriggers let you move safely. You can net a big fish. You can reach the bow. No tipping fear. It changes the game.
Bottom line: yes, they work in salt. Pick tough materials. Mount them strong. Rinse every time. They will serve you well.
What Materials Work Best For Saltwater Outriggers?
Material choice decides how long your outriggers last. Salt eats cheap metal. I have seen aluminum turn to dust. Stainless steel is king. Grade 316 is best. It resists salt. It costs more. But it lasts decades. Look for 316 on the tag.
Aluminum can work if coated. Anodized is okay. Powder coat is better. But scratches let salt in. Then it bubbles. You must touch up nicks fast. I skip aluminum for salt. Too much work.
PVC pipe is cheap and light. It does not rust. But sun makes it brittle. It cracks in cold. Schedule 40 is stronger. Schedule 80 is best. Paint it for UV protection. White paint reflects heat. It helps.
Fiberglass poles are strong. They flex but do not bend. They resist salt. They cost more than PVC. But they last. I like them for long arms. They do not vibrate much.
Floats matter too. Foam-filled plastic is top choice. They never sink. They take hits. They shrug off barnacles. Inflatable floats work but puncture. One barnacle ends your day. I avoid them.
Hardware must be stainless. Bolts, nuts, washers. Grade 316 again. Galvanized fails fast. The zinc coating goes. Then rust blooms. Spend the extra dollars. It is cheap insurance.
Bushings help. Nylon or Delrin. They isolate metals. No galvanic corrosion. Aluminum to stainless eats aluminum. Plastic stops this. Small part, big job.
Paint or coat all metal. Even stainless gets tea stains. A wax coat helps. I use boat wax. It beads water. Salt washes off easy. Do it monthly.
Wood parts? Only marine ply. Seal all edges. Epoxy coat is best. Varnish fails in sun. Epoxy holds. Then paint over epoxy. UV kills bare epoxy.
My setup: 316 stainless arms. Foam-filled polyethylene floats. Nylon bushings. 316 hardware. Five years in salt. Zero rust. It works.
How Do You Protect Outriggers From Salt Corrosion?
Salt corrosion is the main killer. It starts fast. You must fight it daily. Rinse is rule one. Fresh water after every trip. Hit every joint. Hit every bolt. Hit the floats. Salt hides in threads. It hides in seams.
I keep a hose at the dock. Two minutes does it. No soap needed. Just water volume. Let it drip dry. Do not store wet. Water traps salt. Dry gear lives longer.
Coat threads with anti-seize. Blue marine grease works. Teflon gel works. Do this at install. Do it each time you adjust. It stops galling. It seals out salt. Bolts turn free years later.
Wax the arms. Car wax or boat wax. It fills pores. Salt slides off. Rain washes it clean. Do this monthly in season. Twice a year minimum.
Check anodes if you have them. Some brackets take zincs. Replace when half gone. They save your stainless. Cheap insurance. I tape a spare to my trailer.
Store outriggers off the boat. Sun and salt attack 24/7. A garage rack is best. Or a shaded shed. UV kills plastic. Heat kills grease. Cool dark storage wins.
Inspect monthly. Look for white powder. That is aluminum corrosion. Look for brown tea stains. That is stainless surface rust. Catch it early. Scrub with Scotch-Brite. Re-wax.
Lubricate moving parts. Pivot pins. Folding hinges. A drop of oil monthly. Work it in. Wipe excess. Dirt sticks to extra oil. Clean works best.
Cover the floats. Sun fades plastic. Cracks form. Water enters. Foam stays dry if skin holds. A tarp or bag helps. Cheap. Effective.
My routine: rinse, dry, wax, store. Ten minutes. Gear looks new. No surprises. Do you have a routine? Start one today.
Do Outriggers Affect Jon Boat Performance In Saltwater?
Yes, outriggers change how your boat runs. They add width. They add drag. They add weight. But they add stability. It is a trade. You decide what matters.
Speed drops. Expect two to five mph loss. Depends on motor. Depends on hull. A 20 hp motor feels it more. A 60 hp barely notices. Drag comes from floats in water. Arms in air add wind drag.
Fuel use rises. The motor pushes harder. You burn more gas. Plan for it. Carry extra fuel. Or accept shorter range. I budget ten percent more fuel.
Planing takes longer. The boat needs more speed to lift. Floats hold the stern down. Trim helps. Trim up a bit. Find the sweet spot. Each boat differs.
Turning changes. Wide stance resists lean. The boat stays flat. Good for comfort. Bad for tight turns. You need wider arcs. Practice in open water. Learn the new feel.
Wind pushes you more. Arms act like sails. Side wind drifts you. Anchor or drift sock helps. I carry a drift sock. It steadies the boat. Fishing gets easier.
Weight adds up. Arms, floats, hardware. Fifty to eighty pounds typical. On a small jon boat, that counts. Move weight forward. Balance the load. Keep the bow down.
Shallow water? Floats hit bottom first. They protect the hull. But they limit skinny water. Raise them if you can. Some fold up. Mine flip up. I run skinny creeks fine.
Waves feel different. The boat rocks less. But it snaps back faster. Quick motion. Some folks get seasick. Test before a long trip. Short runs first.
Overall? I keep mine on. Stability wins. I catch more fish. I feel safe. The speed loss is small. The peace of mind is big.
What Size Outriggers Do You Need For A Jon Boat?
Size depends on your boat width. And your use. Wider boats need less. Narrow boats need more. A 48-inch beam needs long arms. A 60-inch beam needs less. Measure your beam first.
Arm length: 30 to 48 inches out. Each side. Total width doubles. A 48-inch boat with 36-inch arms hits 120 inches. That is ten feet. Check trailer width. Check garage door. Check state law.
Float size: 30 to 50 inches long. Four to six inches diameter. Bigger floats displace more. They resist lean more. But they drag more. Match float to boat weight. Heavier boat needs bigger floats.
My 14-foot jon is 48 wide. I use 36-inch arms. 40-inch floats. Five-inch diameter. Perfect balance. Stable but not huge. Fits my trailer. Legal in my state.
Adjustable arms are smart. Telescoping tubes. You shorten for trailering. Extend for fishing. One set does all. Costs more. Worth it. I would not buy fixed again.
Float height matters. At rest, floats kiss water. Under load, they dig in. Too high, they do nothing. Too low, they drag always. Adjustable brackets fix this. Slide up or down.
Small boat? Ten to twelve foot? Go lighter. PVC arms. Small floats. Every pound counts. You can hand-tighten clamps. No tools needed. Easy on, easy off.
Big boat? Sixteen foot plus? Go heavy. Stainless arms. Big floats. Bolt-on mounts. You want zero flex. Big water demands it.
Test fit before drilling. Clamp arms on. Set floats. Sit in boat. Lean hard. Feel the support. Adjust. Mark holes. Then drill. Measure twice.
Remember: you can trim later. Cut arms shorter. Trim floats. But you cannot add length. Buy a bit long. Trim to fit. Smart money.
How Do You Install Outriggers On A Jon Boat For Saltwater?
Install is not hard. But it must be strong. Salt water tests every joint. Weak spots fail fast. Take your time. Do it right once.
Pick mount points. Transom is common. Gunwale works too. Transom shares load across width. Gunwale is easier. I use transom. Stronger. Cleaner look.
Backing plates are mandatory. Half-inch marine ply. Or thick aluminum. Three by six inches minimum. One per bolt. Four bolts per side. Eight plates total. They spread the load.
Drill holes. Use a sharp bit. Slow speed. Clean holes. Chamfer edges. Sealant in every hole. Butyl tape or 3M 4200. Fill the hole. Coat the bolt. No dry holes.
Bolt pattern: two high, two low. Vertical spacing six inches. Horizontal spacing twelve inches. This triangle resists twist. It handles side loads. It handles up loads.
Use fender washers. Big ones. Stainless. They spread clamp force. They protect the gel coat. They seal better. Two per bolt. One each side.
Nylock nuts. They vibrate loose otherwise. Blue Loctite on threads. Hand tight plus half turn. Do not crush the wood. Snug is enough. Check after first trip.
Run a bead of sealant around base. Smooth with finger. Let cure twenty-four hours. Launch after cure. Water finds gaps. Sealant stops it.
Attach arms. Set float height. Level the boat. Floats touch water. Tighten clamps. Mark position. Drill pin holes. Lock pins in. Safety wire the pins.
Test load. Two adults on one gunwale. Boat should stay level. Floats take weight. No hull lean. Adjust if needed. Then fish.
Can You Use Inflatable Outriggers In Saltwater?
Yes, you can. But I do not recommend them. Salt water has barnacles. It has oyster shells. It has sharp debris. One poke and your float is flat. Your stability is gone. You are far from shore. Bad day.
Inflatables are light. They store small. They cost less. They work in calm fresh water. Lakes. Ponds. Slow rivers. But salt is rough. Dock pilings. Anchor lines. Crab pots. All sharp.
UV kills the fabric. Sun bakes them. They get sticky. They get brittle. Seams split. Two seasons max in Florida sun. I have thrown away three sets. Waste of money.
Repair kits exist. Patches and glue. But salt water prevents bonding. Wet surface, no stick. You must dry it fully. Hard on the water. Hard in humidity.
Pressure changes with heat. Morning cold, low pressure. Afternoon hot, high pressure. Pop risk. You must bleed air. Or they burst. Foam floats do not care.
Some have tough covers. Hypalon or PVC skin. Better. But still puncture. And the cover hides damage. You don’t see the leak. Until it fails.
If you must use inflatables, carry spares. Carry a pump. Carry patches. Carry glue. Check pressure often. Baby them. But why bother?
Foam-filled costs more upfront. But ten years later, they still work. No pumps. No patches. No worry. Hit a piling? Bounce off. Keep fishing.
My buddy swears by his inflatables. He fishes calm bays. He watches depth. He stores them inside. They last him three years. He accepts the work. You decide.
For me? Foam all day. Peace of mind. No nurse-maiding gear. I fish. Gear handles itself.
What Maintenance Do Saltwater Outriggers Need?
Maintenance is simple. But it must be regular. Salt never sleeps. You cannot skip. A little often beats a lot rarely.
Rinse after every trip. Fresh water. High volume. Hit every surface. Inside tubes. Under brackets. Behind floats. Salt hides everywhere. Two minutes saves hours.
Dry before storage. Towel off. Air dry an hour. No wet bags. No damp lockers. Moisture breeds corrosion. Dry gear lasts.
Monthly wax. Arms, brackets, hardware. Carnauba wax. Marine wax. Wipe on, wipe off. Water beads. Salt rinses. Looks good too.
Check bolts quarterly. Wrench check. Snug any loose. Look for rust streaks. White powder on aluminum. Brown tea on stainless. Clean and re-wax spots.
Lube pivots. Silicone spray. Or light oil. Work the joint. Wipe excess. Grit sticks to wet lube. Dry lube is better. Teflon spray works.
Inspect floats. Look for cracks. Look for gouges. Press hard. Feel for soft spots. Waterlogged foam gets heavy. Replace if soft. They lose buoyancy.
Check anodes. If your kit has zincs. Replace at half gone. Put a reminder on phone. Forgotten anodes do zero good.
Store smart. Off the boat. Vertical rack. Arms up. Floats off ground. Covered. Cool. Dark. Rodents chew foam. Keep critters out.
Seasonal deep clean. Pull pins. Disassemble. Clean threads. Fresh anti-seize. Reassemble. Torque to spec. One hour a year. Prevents seized nightmares.
Keep a log. Date. What done. What seen. Next due. Simple notebook. Stays in boat. No memory needed. Discipline beats memory.
Are Homemade Outriggers Safe For Saltwater Use?
Homemade can work. But safety is on you. No engineer checked it. No warranty. No recall. You own every failure. I have built them. I have seen them fail.
Materials must be marine grade. No hardware store pipe. No plumbing PVC. Schedule 80 electrical conduit is okay. But UV kills it. Paint it well.
Wood arms? Only if you know wood. Douglas fir. Clear grain. Epoxy sealed. Varnish fails. Epoxy holds. But wood fatigues. It cracks unseen. I avoid wood arms.
Floats: foam-filled pipe. Or plastic drums. Drums must be sealed. One leak and it sinks. Foam pipe is safer. Closed cell foam. No water entry.
Mounts are the weak link. Homemade brackets bend. Welds crack. Bolts pull through. Overbuild everything. Triple what you think. Steel gussets. Thick plates.
Test thoroughly. Calm water. Load boat. Lean hard. Jump on gunwale. Watch for flex. Watch for leaks. Watch for loose bolts. Fix every issue.
Label capacity. Write max load on arm. Do not exceed. Guests don’t know limits. You do. Enforce it.
Inspect before every trip. Serious look. Wiggle test. Torque check. Salt fatigues metal fast. Fatigue fails without warning. Be paranoid.
Insurance may not cover homemade. Check your policy. Some exclude DIY mods. A claim denial hurts. Know before you go.
My advice: buy a proven kit. Engineering is done. Testing is done. Warranty exists. Support exists. Your time is worth more. Fish more. Build less.
How Much Do Saltwater Jon Boat Outriggers Cost?
Cost varies wide. Budget to premium. You get what you pay for. But mid-range often wins. Let us break it down.
DIY PVC: fifty to hundred dollars. Pipe, floats, clamps, hardware. Your labor free. Lasts one to three years. Good for trying. Good for rare use.
Basic aluminum kit: two to four hundred. Coated arms. Plastic floats. Clamp mounts. Lasts two to five years. Rinse well. Touch up scratches.
Mid stainless kit: five to eight hundred. 316 arms. Foam floats. Bolt-on mounts. Lasts ten plus years. My choice. Best value.
Premium telescoping: one to two thousand. Adjustable length. Quick release. Fancy floats. Lasts forever. For serious daily use. Charter grade.
Used market exists. Check classifieds. Marina boards. Boat shows. Stainless lasts. Used stainless is like new. I bought my set used. Half price. Five years later, perfect.
Install cost: zero if DIY. Two hundred if shop. Shop ensures strength. Worth it if unsure. Bad install costs more later.
Maintenance cost: twenty a year. Wax. Grease. Anodes. Cheap. Skip it, pay hundreds later. Pay now or pay more later.
Total five-year cost: DIY two hundred. Basic six hundred. Mid eight hundred. Premium two thousand. Mid wins value. Low hassle. High life.
Hidden costs: fuel increase. Ten percent more. Storage space. Trailer width. Garage fit. Measure first. Avoid surprises.
My spend: six hundred used. Twenty a year. Ten years so far. Sixty per year. Best boat money I spent. What is your budget?
Frequently Asked Questions About Jon Boat Outriggers In Saltwater
Do I need outriggers on a wide jon boat?
Wide boats over 60 inches may not need them. But they still help in rough water. They help when standing. They help with heavy loads. Try without first. Add if you want more stability.
Can I leave outriggers on the trailer?
Yes, if they fit legal width. Fold or remove if too wide. Check lights. Check tires. Wide loads need flags. Know your state laws. Measure before you tow.
Will outriggers void my boat warranty?
Usually no. But check your manual. Transom mods might be an issue. Clamp-on avoids holes. Bolt-on may need dealer approval. Keep receipts. Document install.
Can I use kayak outriggers on a jon boat?
No. Too small. Too weak. Jon boats weigh more. Forces are higher. Kayak gear will bend or break. Buy jon boat rated gear. Size matters.
How fast can I run with outriggers deployed?
Run at comfortable plane speed. Usually 20 to 30 mph. Floats may skip at high speed. Trim up reduces drag. Slow down in chop. Safety first.
Final Thoughts
Outriggers transform a jon boat in salt water. They give stability. They give confidence. They let you fish hard. But they need salt-smart choices. Stainless arms. Foam floats. Strong mounts. Regular rinse. That is the formula. I have fished this way for years. It works. My boat feels like a platform. Not a tippy tub. You can do this too. Pick your kit. Mount it right. Care for it. Then go catch fish. The water is waiting. Be safe. Have fun. Tight lines.