How to Build DIY Jon Boat Outriggers: A Step-by-Step Guide
Looking for a steadier jon boat? A set of DIY outriggers will do the trick. You can knock them out in a single day, and they cost a fraction of what you’d pay for a factory kit. This guide walks you through every step. All you need are basic tools, simple materials, and zero welding experience. Ready to give your boat a rock‑solid stance?
Estimated Time: 4 to 6 hours
Difficulty Level: Easy to Moderate
Primary Objective: Build and mount stable outriggers for a jon boat
Before You Start: Tools, Gear & Preparation
Collect everything before you make the first cut. Work on a flat, level surface and keep kids and pets clear of the area. Slip on safety glasses and gloves, and check the forecast—rain or high wind will only slow you down.
| Item / Tool | Purpose | Optional / Required |
|---|---|---|
| PVC pipe (2 inch, Schedule 40) | Main arms and cross bars | Required |
| PVC elbows and tees (2 inch) | Connect pipes at angles | Required |
| PVC cement and primer | Bond joints tight | Required |
| Pool noodles or foam floats | Add buoyancy to arms | Required |
| U-bolts with nuts and washers | Mount arms to boat | Required |
| Stainless steel bolts (1/4 inch) | Secure brackets to gunwale | Required |
| Marine plywood pads (1/2 inch) | Spread load on gunwale | Required |
| Hacksaw or PVC cutter | Cut pipe to length | Required |
| Drill and bits | Drill mount holes | Required |
| Wrench set | Tighten U-bolts | Required |
| Measuring tape | Mark cut lengths | Required |
| Marker pen | Mark cuts and holes | Required |
| Sandpaper (80 grit) | Prep PVC for glue | Required |
| Duct tape or zip ties | Hold floats in place | Optional |
| Stainless steel cable | Add diagonal bracing | Optional |
| Turnbuckles | Tension the cables | Optional |
Safety Check: Disconnect the battery, clear loose gear from the deck, and make sure the boat sits level on its trailer or blocks. You’ll need unobstructed access to both gunwales.
Step 1: Measure Your Boat and Plan the Layout
Measure the beam at its widest point, then add 12 inches per side for the outrigger reach. Mark the mounting points on each gunwale, spacing them 24 inches apart fore and aft. That gives you a wide, stable base. If you have a center console, place the forward arm ahead of it and the aft arm behind it.
Write down every length you’ll need—front arm, rear arm, cross bar, float sections. Double‑check each number; a bad cut wastes pipe. Remember: measure twice, cut once.
Step 2: Cut the PVC Pipe to Length
Lay the pipe on sawhorses, mark each cut with your marker, and slice cleanly with a hacksaw or PVC cutter. Deburr the ends with 80‑grit sandpaper—rough edges weaken the glue joint. You’ll need four long arms, two cross bars, and four short vertical risers. Tag each piece with tape so nothing gets mixed up.
Typical lengths for a 14‑foot jon boat: arms 48 in., cross bars 36 in., risers 12 in. Adjust for your beam width, but keep the arms a little long—you can trim later, you can’t add length back.
Step 3: Dry Fit the Frame Assembly
Push the pieces together without glue, building one side at a time. Slip an elbow onto each end of the cross bar, insert a riser into each elbow, then push an arm into each riser. Cap the outer end of each arm with a tee (the tee points down for the float mount). Step back and eyeball the shape—does it clear the oarlocks? The motor? Adjust now; once you glue, there’s no going back.
Step 4: Glue the PVC Joints
Work in a well‑ventilated spot. Prime every socket and pipe end, let the primer flash for about 10 seconds, then coat both surfaces with cement. Join them with a quarter turn, hold for 30 seconds, and wipe away excess. Do one joint at a time: cross‑bar elbows first, then risers, then arms, then the outer tees. Let the whole frame cure for 15 minutes before moving it.
Captain’s Note: Cold weather slows the cure; warm the pipe in the sun first. Hot weather speeds it up—work fast when it’s warm.
Step 5: Attach the Floats
Slide pool noodles over each arm, pushing them to the outer tees. Two noodles per arm work well; cut each to 48 in. Secure them with zip ties or duct tape at the tee and at the arm tip. For extra buoyancy, bolt foam dock floats through the tee outlets using fender washers to prevent pull‑through. The floats should sit just below the gunwale line when the boat rests level.
Test the float depth by setting the frame on the boat. The floats should kiss the water at rest without dragging. Trim the noodles if they sit too low.
Step 6: Build the Mounting Brackets
Cut four 6 × 6‑in. marine plywood pads and drill a ¼‑in. hole in each corner—these spread the U‑bolt load. Size the U‑bolts to your gunwale thickness (most jon boats need 2‑in. U‑bolts). Thread a nut onto each end, place a pad inside the hull and one outside, run the U‑bolt through both, and snug the nuts. Don’t crush the gunwale; the bracket must stay rigid.
Step 7: Mount the Outrigger Arms to the Boat
Lift the frame into position and rest the inner arm ends on the U‑bolts. Mark where each arm crosses a U‑bolt, drill a ¼‑in. hole through the arm at each mark, then bolt the arm to the U‑bolt saddle using a flat washer, lock washer, and nut. Tighten with a wrench. Verify the frame sits level—floats should be even port and starboard. Adjust U‑bolt height if needed.
Trail Hack: Add a second U‑bolt 12 in. forward on each side. Two attachment points lock the arm against twist—two points are always better than one.
Step 8: Add Diagonal Bracing (Optional but Recommended)
Run stainless‑steel cable from the outer float tee to the forward mount point on each side. Use a turnbuckle to tension the cable. Repeat aft. The resulting triangle prevents the arm from folding back. Cut cable with bolt cutters, swage the ends or secure with three cable clamps per end, torque to spec, and tighten the turnbuckles until the cable “sings.” Don’t over‑tighten—the frame needs a tiny bit of flex.
Step 9: Test on the Water
Launch the boat, load your normal gear, and settle into your fishing spot. Rock the boat hard. The outriggers should resist the roll, keeping the floats half‑submerged. No float should leave the water, and no arm should bend. After 15 minutes, re‑check every bolt—vibration loosens nuts. Retighten as needed.
See any splash? Raise the floats a touch. Notice a lean? Tweak the cable tension. When it’s dialed in, the boat feels planted, as if it grew wider overnight.
Common Mistakes & Troubleshooting
Problem: Arms Bend Under Load
Cause: Pipe too thin or span too long.
Fix: Upgrade to Schedule 80 PVC or add a center support strut from the cross bar to the arm midpoint.
Problem: Floats Drag at Speed
Cause: Arms mounted too low.
Fix: Raise the U‑bolts or shorten the risers. Floats should clear the water by about 2 in. at planing speed.
Problem: Frame Twists on Waves
Cause: Single mount point per side.
Fix: Add the forward U‑bolt and diagonal cables. Triangles don’t twist.
Problem: PVC Cracks at Joints
Cause: No primer or glue applied in cold conditions.
Fix: Cut out the bad joint, clean the pipe, re‑prime and re‑glue after warming the pipe.
Problem: Boat Lists to One Side
Cause: Unequal float buoyancy or arm length.
Fix: Measure both sides, match float volume and arm length. A slightly shorter arm on the heavy side helps.
Frequently Asked Questions About DIY Jon Boat Outriggers
How much do DIY jon boat outriggers cost?
Expect to spend $80–$150. PVC and floats are cheap; hardware is the main expense. Scoring used U‑bolts can shave a few bucks.
Can I use wood instead of PVC?
Yes. 2×4 lumber works for arms—seal it with epoxy paint. Wood is heavier but stiffer; it will rot if not sealed properly.
Do outriggers affect boat speed?
Minimal drag at low speed. At planing speed, keep the floats clear of the water and they add virtually no resistance.
How wide should jon boat outriggers be?
A total width of 8–10 ft works well—about 3–4 ft out per side. Wider equals more stability but makes trailering tougher.
Can I remove them for trailering?
Absolutely. Use quick‑release pins on the U‑bolts. Pull four pins, lift the frame off, and store it flat on the trailer.
Final Thoughts
You built it, you tested it—now fish the rough water. Stand up to cast, shift side to side, and the boat stays flat. That’s the payoff: a bigger, steadier platform for a modest price. Check the bolts every trip, swap the noodles each season, and the frame will last for years. Get out there; the water’s waiting.