how to maintain jon boat outriggers: 5 Tips

How to Maintain Jon Boat Outriggers: A Step-by-Step Guide

how to maintain jon boat outriggers

Do you want your jon boat to stay stable on rough water? Outriggers help a lot. But they need care to work well. This guide shows you how to maintain jon boat outriggers fast and easy. You will learn to clean, check, and fix them like a pro.

Estimated Time: 30 to 60 minutes
Difficulty Level: Easy
Primary Objective: Keep outriggers strong, safe, and ready for every trip

Before You Start: Tools, Gear & Preparation

Get your gear ready first. Work on flat ground. Put the boat on a trailer or blocks. Make sure the outriggers are down and locked. Wear gloves and safety glasses.

Item / Tool Purpose Optional / Required
Fresh water hose Rinse off salt and dirt Required
Mild boat soap Clean without damage Required
Soft brush Scrub tubes and brackets Required
Marine grease Lube moving parts Required
Wrench set Tighten bolts and nuts Required
Screwdriver set Check screws and clips Required
Flashlight See inside tubes Required
Silicone spray Protect metal parts Optional
Replacement pins Swap worn lock pins Optional
Sandpaper (fine) Smooth small scratches Optional
Marine epoxy Fix small cracks Optional

Captain’s Note: Rinse outriggers after every salt water trip. Salt eats metal fast. A quick hose down saves big money later.

Step 1: Rinse and Wash All Parts

Start with a full rinse. Use a hose with a spray nozzle. Hit the tubes, brackets, and arms. Get into the joints. Wash away mud, salt, and fish slime.

Mix boat soap in a bucket. Use warm water. Dip the soft brush. Scrub each tube from end to end. Clean the brackets too. Don’t forget the mounting plates on the boat.

Rinse all soap off. Soap left on can dull the finish. Check the water runs clear. Dry with a clean towel or let air dry.

Trail Hack: Keep a brush and soap bucket in your truck. Wash at the ramp before you drive home. It takes five minutes.

Step 2: Inspect Tubes for Damage

Look at each tube close up. Use the flashlight. Check for cracks, dents, or soft spots. Press on the tube walls. They should feel firm.

Check the ends where caps sit. Water can get in there. If you see white powder on aluminum, that is corrosion. Sand it light and wipe clean.

If a tube holds water inside, drill a small drain hole at the low end. Seal it with a rubber plug. This lets water out but keeps air in.

Captain’s Note: A small crack can grow fast. Fix it now with marine epoxy. Wait 24 hours before use.

Step 3: Check All Bolts and Hardware

Grab your wrench set. Go bolt by bolt. Start at the boat mount. Move to the arm pivots. End at the tube clamps.

Tighten any loose nuts. Don’t over tighten. Aluminum strips easy. Use a torque wrench if you have one. Specs are usually 15 to 20 foot pounds.

Look at the lock pins. Pull each one. Check for bend or wear. The spring should snap back hard. Swap bad pins now.

Check U-bolts on the tubes. They can loosen from vibration. Tighten them in a cross pattern. Top, bottom, left, right.

Step 4: Lubricate Moving Parts

Moving parts need grease. Hit the pivot points on the arms. Grease the slide tubes if they telescope. Grease the lock pin holes.

Use marine grease. It stays put in water. Wipe off extra. Dirt sticks to globs of grease.

Spray silicone on the stainless bolts. It stops rust. Don’t spray on the tube grips. They get slick.

Trail Hack: Do this at the start of each season. And after any long trip. It takes two minutes.

Step 5: Test Deployment and Lock

Now test the action. Fold the arms in. Push them out. They should move smooth. No binding. No grind.

Lock them in the out position. Pull hard on each arm. It should not budge. Try to shake the tube. No play means it’s solid.

Fold them back in. Lock them for travel. The travel lock must hold. If it slips, adjust the catch or add a safety pin.

Have a buddy watch from the side. They can see wobble you might miss.

Step 6: Check Flotation and Ballast

Some outriggers have foam inside. Some are air only. Know yours. If foam, squeeze the tube. It should not squish.

If air chambers, check the valves. Inflate to spec. Spray soapy water on valves. Bubbles mean leaks. Tighten or replace valves.

Check the weight rating on the tag. Don’t overload. Too much weight bends arms or snaps mounts.

Captain’s Note: Write your max load on the arm with a marker. Quick reference when you load gear.

Step 7: Protect for Storage

If the boat sits for weeks, do extra care. Coat all metal with silicone spray. Cover tubes with UV cloth. Sun eats plastic and foam.

Remove the lock pins. Grease them. Store in a zip bag taped to the console. You won’t lose them.

If trailered outside, tilt arms down. Water drains off. Ice won’t split tubes.

Check straps on the cover. Wind flaps tear fabric. Tight is right.

Common Mistakes & Troubleshooting

Problem Cause Quick Fix
Arm won’t lock out Dirt in lock hole or bent pin Clean hole. Straighten or replace pin
Tube wobbles at speed Loose U-bolts or worn bushings Tighten U-bolts. Replace bushings
Rust on stainless bolts No silicone coat Wire brush clean. Spray silicone
Water inside tube Bad end cap seal Drill drain hole. Add plug. Reseal cap
Arm binds when folding Dry pivot or bent arm Grease pivot. Check for bend
Mount plate cracks Over torque or fatigue Stop use. Weld or replace plate

See a crack on a mount? Stop. That is a safety issue. Get a welder or a new plate. Don’t risk a flip.

Frequently Asked Questions About How to Maintain Jon Boat Outriggers

How often should I rinse my outriggers?

Rinse after every trip in salt water. Rinse weekly in fresh water. Salt and mud cause fast wear.

Can I use car wax on the tubes?

Yes. Car wax protects aluminum and plastic. Apply twice a year. Buff by hand.

What grease is best for pivots?

Marine grade lithium grease. It resists water washout. White color shows where you put it.

Do I need to remove outriggers for winter?

Not if stored dry and covered. But remove pins and grease them. Tilt arms down to drain.

How do I know if foam is waterlogged?

Tube feels heavy. One side sits lower. Drill a hole. If water pours out, foam is shot. Replace tube.

Final Thoughts

You now know how to maintain jon boat outriggers from top to bottom. Clean them. Check them. Grease them. Test them. Store them right. It takes less than an hour. That hour saves you a bad day on the water.

Grab your brush. Hit the ramp. Keep your ride steady and safe. Tight lines and calm water.

Leave a Comment