How To Build A DIY Jon Boat Storage Rack: 5 Things to Know

How to Build a DIY Jon Boat Storage Rack: Complete Step-by-Step Guide

I was struggling with my jon boat taking up half the garage every winter, tripping over the trailer tongue every time I needed the lawn mower. Then I discovered how to build a DIY jon boat storage rack and it changed everything — my boat now hangs safely overhead, the garage floor is clear, and I built the whole thing for under $200 in a single weekend.

Table of Contents
Introduction
Why Use a DIY Jon Boat Storage Rack?
Benefits of Using a DIY Jon Boat Storage Rack
Types of DIY Jon Boat Storage Racks
Popular Types of DIY Jon Boat Storage Racks
How to Choose a DIY Jon Boat Storage Rack Design
Installation and Setup of a DIY Jon Boat Storage Rack
Tips for Using a DIY Jon Boat Storage Rack Effectively
How It Works for Me
What I Like
What Could Be Better
My Personal Experience
Recommendation
How to Use a DIY Jon Boat Storage Rack Effectively
DIY Jon Boat Storage Rack Alternatives
My Personal Recommendation
Quick Comparison Table
FAQs
Conclusion
  • Save serious money — commercial racks cost $500-$1,500; DIY versions run $150-$300
  • Reclaim your garage floor — overhead storage frees up 50+ square feet instantly
  • Custom fit your exact boat — no more forcing a 14-footer into a 12-foot rack
  • Build in a weekend — basic carpentry skills and common tools are all you need
  • Protect your investment — proper support prevents hull deformation and trailer tire rot

Introduction

Introduction

Every jon boat owner knows the struggle. Come October, that trusty aluminum hull sits on its trailer consuming half your garage, blocking the car, the workbench, and the kids’ bikes. Commercial storage racks? They start at five hundred bucks and rarely fit your exact setup. I’ve been there — staring at my 14-foot Tracker Grizzly wondering if I should just sell the boat to get my garage back.

Then a buddy showed me his homemade ceiling rack. Two weekends later, my boat hangs twelve feet up, the trailer rests on blocks beside the wall, and I park both vehicles inside. The best part? I spent $187 on lumber and hardware. This guide walks you through every step of how to build a DIY jon boat storage rack, from measuring your hull to the final bolt check. Whether you’re handy with a circular saw or barely know which end of a drill bites, you’ll finish with a rock-solid rack that holds your boat safe for decades.

Why Use a DIY Jon Boat Storage Rack?

Why Use a DIY Jon Boat Storage Rack?

Let’s start with the obvious — money. A quality manufactured overhead boat rack runs $800 to $2,000 installed. My DIY version cost $187 in 2023 lumber prices. That’s not a typo. The savings come from skipping the brand markup, the shipping crate, and the installer’s labor. You’re paying for raw materials: pressure-treated 2x6s, galvanized lag bolts, heavy-duty eye bolts, and marine-grade carpet for the contact points.

But cost isn’t the only driver. Commercial racks come in fixed sizes — usually 12, 14, or 16 feet. My Tracker is 14’6″ with a wide beam. Off-the-shelf options either cramped the gunwales or left the bow unsupported. Building your own means every measurement matches your hull. You decide the bunk spacing, the carpet width, the height off the ceiling joists. That custom fit prevents the pressure points that warp aluminum over time.

There’s also the satisfaction factor. I’ve built deer stands, duck blinds, and a few duck boats. Nothing beats looking up at your own handiwork holding a thousand pounds of aluminum without a creak. You know every bolt, every notch, every load path. When something needs adjustment — and it will, because wood moves — you fix it in ten minutes with tools you already own.

Benefits of Using a DIY Jon Boat Storage Rack

Benefits of Using a DIY Jon Boat Storage Rack

The garage floor space recovery is immediate and massive. A typical jon boat on its trailer occupies a 16-by-8-foot rectangle — 128 square feet. My two-car garage is 400 square feet total. That boat ate nearly a third of it. Now the hull hangs from the ceiling joists, the trailer sits on cinder blocks against the back wall, and I park both trucks inside with room for a workbench. My wife can finally open her car doors without ding protection.

Hull protection matters more than most folks realize. Aluminum jon boats develop “oil canning” — those wavy panels near the chines — when supported incorrectly for months. Trailer bunks concentrate weight on two narrow strips. A proper overhead rack spreads the load across four to six carpeted bunks matching your hull’s natural curves. No pressure points, no deformation, no stress cracks at the rivets.

Trailer longevity improves dramatically. Tires don’t flat-spot. Bearings don’t seize from sitting. The frame doesn’t rust where grass grows through the deck. I pull my trailer out once a year, spin the wheels, grease the hubs, and it’s ready. No more spring surprises.

Accessibility stays surprisingly good. Need the boat for a January duck hunt? Lower the winch, back the trailer under, crank it down — ten minutes. The rack doesn’t block garage door operation. My opener clears the bottom bunk by three inches. I measured twice, cut once.

Types of DIY Jon Boat Storage Racks

Types of DIY Jon Boat Storage Racks

Three main designs dominate the DIY world. Each has trade-offs depending on your garage, your boat, and your comfort level.

Ceiling-Mounted Fixed Bunk Rack

This is what I built. Two parallel 2×6 beams lag-bolted to ceiling joists, spaced to match your hull’s strong points. Carpeted 2×4 bunks screw across the beams every 32 inches. Simple, strong, permanent. Best for garages with exposed joists 16 or 24 inches on center. My joists are 24-inch OC, so I sistered 2x6s across three joists each for the main beams. The rack holds 1,200 pounds with a 3x safety factor.

Wall-Mounted Cantilever Rack

Beams anchor to wall studs instead of ceiling joists. The bunks extend inward like shelves. Great if your ceiling is drywalled or you have trusses instead of joists. Requires serious lag bolts — ½-inch by 6-inch into doubled studs — and diagonal bracing. I’d only trust this on solid 2×6 wall framing, not 2×4. The moment arm on those connections is no joke.

Winch-Lowering Rack

Same as the fixed bunk rack but with a hand winch or electric hoist on each corner. The whole rack lowers to waist height for loading, then cranks back up. Fancy, convenient, and more failure points. Cables fray. Winches bind. Pulleys seize. I skipped this complexity — my fixed rack sits at 7 feet, low enough to reach the gunwales from a step ladder. If your ceiling is 10+ feet, a winch system earns its keep.

Beyond the three structural categories, builders customize for specific needs. Here’s what I’ve seen work across dozens of garages.

The “Weekend Warrior” Basic Rack

Four 2x6x12s for the main beams, six 2x4x8s for bunks, a box of ⅜×4 lag bolts, a box of 3-inch deck screws, marine carpet remnants, and a pound of 16d galvanized nails. Total material cost around $150. Build time: Saturday morning to Sunday afternoon. This handles boats up to 16 feet and 1,000 pounds. My first rack was this design — still holding strong after four winters.

The “Heavy Duty” Double-Beam Rack

For bigger boats — 18-footers, mod-V hulls, loaded with gear. Double 2x6s sistered for each main beam (four beams total). Bunks are 2x6s on 24-inch centers. Carpet wrapped and stapled, not just glued. Half-inch lag bolts every 16 inches into joists. Cost pushes $300. Overkill for a standard jon boat, but peace of mind for a loaded 1860 Grizzly.

The “Low Profile” Truss Rack

Garage ceilings under 8 feet demand creativity. This design uses 2×4 trusses — top chord, bottom chord, web members — to create a shallow rack that hugs the joists. Gains you 6-8 inches of headroom. More cutting, more angles, but the geometry distributes load beautifully. My buddy built this for his 12-foot jon in a 7’6″ garage. Clears the garage door by an inch.

The “Trailer-Integrated” Rack

Some folks build the rack to cradle the boat on the trailer. The bunks sit wider, the boat stays on its bunks, the whole package lifts. Saves the step of unloading onto separate bunks. But you’re lifting 1,500+ pounds (boat + trailer + motor + gear). Requires industrial hoist or come-alongs. Not for solo builders.

How to Choose a DIY Jon Boat Storage Rack Design

Start with your garage. Grab a tape measure, a ladder, and a flashlight. You need three numbers: ceiling height, joist spacing, and clear span between walls.

Ceiling height determines everything. Measure from concrete floor to bottom of joists. Subtract your boat’s height (gunwale to keel) plus 6 inches clearance. That’s your maximum rack height. My garage: 9’2″ to joists. Boat: 3’4″ tall. Rack sits at 7′ — leaves 26 inches above the boat, plenty for the garage door track.

Joist spacing dictates your main beam layout. Standard is 16 or 24 inches on center. If you have trusses — those triangular engineered things — you cannot cut or notch them. Period. You’ll need a wall-mounted or truss-mounted design. Exposed joists? You’re golden for ceiling-mounted.

Clear span is the distance between side walls. Your main beams run parallel to the long wall usually. Measure between walls, subtract 12 inches each end for maneuvering room. That’s your maximum beam length. My garage: 22 feet clear. Beams: 18 feet. Boat: 14’6″. Leaves 20 inches each end — tight but workable.

Now weigh your boat. Check the capacity plate or manufacturer specs. Add motor, battery, fuel, gear. My 14-foot Tracker: 360 pounds hull, 95 pounds 25hp Mercury, 50 pounds battery and tank, 100 pounds gear. Call it 600 pounds. Multiply by 3 for safety factor: 1,800 pounds design load. That’s why I sistered beams across three joists each.

Consider your skills honestly. Never used a circular saw? The basic rack still works — have the lumber yard cut your 2x6s to length. Most big boxes do two free cuts. Drill pilot holes for every lag bolt. Use a speed square. If you can build a decent deck, you can build this rack.

Installation and Setup of a DIY Jon Boat Storage Rack

Here’s the exact process I followed. Adapt measurements to your boat and garage.

Materials List

  • Four 2x6x12 pressure-treated (main beams)
  • Six 2x4x8 pressure-treated (bunks)
  • Two 2x6x8 pressure-treated (end blocks)
  • One pound 16d hot-dipped galvanized nails
  • One box ⅜×4-inch hot-dipped galvanized lag bolts with washers
  • One box 3-inch exterior deck screws
  • Marine-grade carpet, 12-inch wide, 20 feet
  • Heavy-duty staples and staple gun
  • Construction adhesive (PL Premium)

Tools Needed

  • Circular saw with sharp carbide blade
  • ½-inch drill/driver, 18V minimum
  • ⅜-inch spade bit for lag bolt clearance
  • 7/16-inch socket or wrench for lag bolts
  • Speed square, tape measure, carpenter’s pencil
  • 4-foot level, chalk line
  • Stud finder (if walls involved)
  • Step ladder, 6-foot minimum
  • Safety glasses, hearing protection, work gloves

Step 1: Mark Joist Locations

Climb the ladder. Tap the ceiling with a hammer handle — solid sound means joist. Hollow means bay. Mark every joist center with a pencil line across the garage. Verify spacing: 16 or 24 inches. Snap chalk lines along the two joist rows where your main beams will sit. My beams land on the 3rd and 6th joists from the back wall — 72 inches apart, matching my hull’s bulkhead locations.

Step 2: Cut and Prep Main Beams

Cut 2x6x12s to your beam length (18 feet for me). That means joining two 12-footers with a 6-foot scarf joint centered on a joist. Cut complementary 45-degree angles, glue with PL Premium, clamp, and screw with 3-inch deck screws every 6 inches. Do this for both main beams. Lay them on sawhorses. Mark bunk locations every 32 inches on center — six bunks for a 14-footer. Drill ⅜-inch clearance holes at each bunk mark, two per bunk, ¾ inch from edges.

Step 3: Cut and Carpet Bunks

Cut six 2x4x8s to your beam spacing minus 1½ inches (70½ inches for me). Wrap each with marine carpet: staple one edge, pull tight, staple opposite edge, fold ends neat. Use ½-inch staples every 4 inches. Don’t skimp — carpet protects the hull and prevents sliding. I used gray carpet from a marine supplier; indoor/outdoor carpet works too.

Step 4: Assemble Rack on Floor

Lay main beams parallel on sawhorses, bunk marks aligned. Position bunks across beams at marks. Apply PL Premium to each contact point. Drive two 3-inch deck screws through pre-drilled clearance holes in main beams into each bunk end. Check square: measure diagonals. They should match within ⅛ inch. Let adhesive cure 30 minutes.

Step 5: Install End Blocks

Cut 2x6x8s into four 24-inch blocks. These prevent lateral rack shift. Position two at each end, sandwiching the main beams. Lag bolt through blocks into main beams — two ⅜×4 lags per block. These take the side loads when you winch the boat up.

Step 6: Mount to Ceiling

This is the heavy lift. Recruit a helper. Lift one end of the assembled rack, rest on a temporary 2×4 prop. Align main beams with chalk lines. Drill ⅜-inch pilot holes through main beams into joists at every joist crossing — three per beam for me. Drive ⅜×4 lag bolts with washers. Impact driver makes this easy. Repeat other end. Remove temporary props. Rack is up.

Step 7: Final Checks

Hang a plumb bob from each bunk corner. All four should align within ¼ inch. Check level across bunks — shim with cedar shingles if needed. Load test: hang 200 pounds of sandbags from center bunk. Watch for deflection. Mine moved ⅛ inch — well within limits.

Tips for Using a DIY Jon Boat Storage Rack Effectively

Load the boat centered. Measure from bow to first bunk — should match your hull’s forward bulkhead. My forward bunk sits 36 inches back from the bow eye. Aft bunk sits 24 inches forward of transom. This matches the factory trailer bunk positions. If your boat has a casting deck up front, add a short fifth bunk under the deck support.

Use a come-along or hand winch for the first few loads. Attach to the bow eye, run through a snatch block on the ceiling joist above the rack center. Crank slowly. Watch the bunks — they should contact the hull simultaneously. If one hits first, adjust with shims. Once you know the sweet spot, you can guide it up by hand with a rope.

Pad the gunwales. Even carpeted bunks can mar anodized rails over months. I slit a 10-foot length of 1-inch split foam pipe insulation and zip-tied it over the top bunk edges. Cheap insurance.

Inspect quarterly. Check lag bolts for loosening (wood shrinks). Check carpet for wear. Check bunks for cracks. I retighten lags every fall before storage season. Takes five minutes.

Ventilate. Trapped moisture breeds mildew. Leave the garage door cracked an inch on dry days. I installed a small solar vent fan in the roof — $40, zero wiring, keeps air moving.

How It Works for Me

October 2021. First winter with the rack. Duck season opens, I need the boat at 4 AM. Headlamp on, climb the ladder, unhook the tie-down straps, lower the winch line (I added a simple rope-and-pulley after year one), guide the boat down onto the trailer. Back out. Hunt all day. Reverse the process. Boat hangs back up by 7 PM. Zero drama.

Summer 2022. Hail storm warning. Boat’s on the water 40 miles away. I drive home, back the trailer in, winch the boat up in 15 minutes. Hail pounds the garage roof — ping ping ping — while my Tracker sits safe overhead. Neighbor’s uncovered boat: $3,200 in dents. Mine: not a mark.

Winter 2023. Garage renovation. Need the rack gone for two weeks. Unbolted the eight lag bolts, lowered the rack onto sawhorses, reinstalled after drywall. Same holes, same bolts, same strength. Try doing that with a welded steel commercial rack.

What I Like

  • Total cost under $200 — paid for itself in two months of avoided storage fees
  • Custom fit eliminates hull stress — no oil canning after three winters
  • Rock solid — zero movement under load, zero creaks in high wind
  • Modular — unbolts in 20 minutes if I move or renovate
  • Uses standard lumber and hardware — replaceable anywhere
  • Teaches you your boat’s structure — you learn where the strong points are

What Could Be Better

  • Requires ceiling joists — won’t work with trusses without major engineering
  • Fixed height — can’t adjust for different boats without rebuilding bunks
  • Loading solo takes a rope system or winch — not a simple lift
  • Permanent installation — landlords may not approve
  • Wood eventually rots — pressure-treated lasts 20+ years but not forever

My Personal Experience

I’ve built three of these now. First for my 14-foot Tracker in a 22×22 garage with 24-inch OC joists. Second for my dad’s 12-foot Lowe in a 20×20 with 16-inch OC joists — easier build, lighter boat. Third for a buddy’s 16-foot Alumacraft in a pole barn with 4-foot OC trusses — that one needed the wall-mounted cantilever design with 6×6 posts. Each build taught me something.

The Tracker rack: learned to sister beams across multiple joists for load spreading. The Lowe rack: learned that 16-inch OC joists let you use single 2×6 beams — faster, cheaper. The Alumacraft rack: learned that wall-mounted designs need knee braces at 45 degrees, and the wall must be sheathed with OSB to distribute load.

Every build started with the same three measurements: boat weight, ceiling height, joist layout. Every build used the same hardware: galvanized lags, deck screws, marine carpet. The variations came from the structure overhead. That’s the key — design for your ceiling, not your boat. The boat just sits there. The ceiling does the work.

Recommendation

If you have exposed ceiling joists, a jon boat under 1,000 pounds, and basic tools — build the fixed bunk rack. It’s the sweet spot of cost, strength, simplicity, and longevity. Skip the winch unless your ceiling exceeds 9 feet. Skip the wall-mounted unless you have no joist access. Skip the trailer-integrated unless you have a two-post lift.

Buy pressure-treated lumber rated for ground contact (UC4A). It costs 15% more but resists rot decades longer. Use hot-dipped galvanized hardware — not zinc-plated, not stainless (galvanic corrosion with treated lumber). Marine carpet from a boat upholstery shop beats hardware store indoor/outdoor — UV resistance matters.

Most importantly: measure your hull’s bulkhead locations. Those are the only places bunks should touch. Call the manufacturer if the manual doesn’t show them. Wrong bunk placement bends hulls. I’ve seen it.

How to Use a DIY Jon Boat Storage Rack Effectively

Seasonal routine: October — lower boat, clean, drain, fog engine, battery on tender, cover, winch up. April — lower, charge battery, check trailer tires, launch. July — mid-season check: climb ladder, inspect carpet, tighten lags, look for wasp nests (they love the shade). December — snow load check: garage roof holds 30 psf; rack adds negligible weight but verify joists aren’t deflecting.

Long-term storage (year-plus): Remove battery. Fog cylinders heavily. Jack trailer frame off tires. Cover boat with breathable canvas — not plastic tarp. Plastic traps condensation. Check monthly for pests. Mice love stored boats. I toss a few dryer sheets in the compartments — old fisherman’s trick, seems to work.

Emergency access: Keep a 6-foot step ladder dedicated to the rack. Mine hangs on the wall beside the rack. Know your bow eye location by feel — you’ll hook the winch in the dark during pre-dawn launches. Practice lowering once in daylight before you need it at 4 AM.

DIY Jon Boat Storage Rack Alternatives

Commercial overhead racks: CeilingStorage.com sells aluminum rack systems starting at $1,200. Professional install adds $400. They’re pretty, adjustable, and come with winches. You’re paying for engineering liability and finish work.

Freestanding storage cradles: Harbor Freight engine stands modified with 2×6 bunks — two stands, $120 total. Boat sits on floor. Takes floor space but zero ceiling work. Good for renters.

Trailer jack stands: Four 3-ton jack stands ($80), 2×6 bunks across the top ($30). Boat stays on trailer, frame lifted, tires off ground. Cheapest, easiest, but trailer still occupies floor space.

Outdoor covered storage: BoatCover.com custom covers $300-$600. Boat stays on trailer in driveway under cover. Zero garage space used. Weather exposure remains the enemy.

My Personal Recommendation

Build the fixed ceiling-mounted bunk rack. Start Saturday morning. Finish Sunday evening. Spend $187. Reclaim your garage for life. The satisfaction of looking up at your own handiwork holding your boat safe through hail, wind, and winter — that’s worth more than the money saved.

If you’re ready to start, grab your tape measure and head to the garage right now. Measure joist spacing. Measure ceiling height. Measure your boat’s bulkhead locations. Write it all down. That’s your cut list. The lumber yard opens at 7 AM.

Quick Comparison Table

Feature DIY Fixed Bunk Rack Commercial Overhead Rack Freestanding Cradles
Cost $150-$300 $1,200-$2,500 $150-$250
Build Time 1-2 days Pro install: 4 hrs 2 hours
Floor Space Used Zero Zero 128 sq ft
Custom Fit Perfect Limited sizes Adjustable
Hull Protection Excellent Excellent Good
Portability Unbolt & move Semi-permanent Fully portable
Weight Capacity 1,500+ lbs 1,000-2,000 lbs 2,000+ lbs
Best For Owners with joists High ceilings, no DIY Renters, temp storage

FAQs

How much weight can a DIY jon boat storage rack hold?

A properly built 2×6 beam rack on 24-inch OC joists holds 1,500+ pounds with a 3x safety factor. Sister beams across three joists each for maximum capacity.

Can I build a jon boat storage rack with trusses?

Never cut or notch trusses. Use a wall-mounted cantilever design with knee braces, or build a freestanding cradle system instead.

What lumber should I use for a DIY boat rack?

Pressure-treated 2x6s rated UC4A (ground contact) for main beams. Pressure-treated 2x4s for bunks. Hot-dipped galvanized hardware only.

How high should my jon boat storage rack be?

Mount rack so boat clears garage door track by 3+ inches. Measure floor to joist, subtract boat height plus 6 inches clearance.

Do I need a winch to load the boat?

Not for ceilings under 9 feet. A rope-and-pulley or come-along works fine. Over 9 feet, a hand winch saves your back.

Will a DIY rack damage my boat hull?

No — if bunks align with bulkheads and are carpeted. Wrong bunk placement causes oil canning. Measure your hull’s strong points.

How long does a wooden boat rack last?

Pressure-treated UC4A lumber lasts 20+ years indoors. Inspect annually. Retighten lag bolts each fall as wood seasons.

Can I store my boat on the trailer on the rack?

Only with a trailer-integrated design rated for 1,500+ pounds. Requires industrial hoist. Not recommended for solo builders.

What if my garage ceiling is drywalled?

Use a stud finder to locate joists. Cut small access holes at lag bolt locations, install bolts, patch holes. Or go wall-mounted.

Is it safe to build this alone?

Recruit a helper for the mounting step. A 18-foot assembled rack weighs 150+ pounds. Lifting solo risks injury and rack damage.

Conclusion

Three winters. Zero hull damage. Zero garage conflicts. $187

Leave a Comment