jon boat outrigger installation steps: Easy Guide for Beginners
jon boat outrigger installation steps help you add stability to a small boat. Outriggers keep the boat from tipping when you stand or cast. This guide shows each step in plain language. You will need basic tools and a few hours. The job is easy for most DIYers. Follow the steps to avoid damage and stay safe. Let’s get started.
Time: about 2 hours. Difficulty: easy. Goal: attach outriggers securely.
Table of Contents
- Before You Start: Tools, Gear & Preparation
- Step 1: Measure and Mark Mounting Points
- Step 2: Drill Pilot Holes
- Step 3: Attach Brackets to Hull
- Step 4: Mount Outrigger Arms
- Step 5: Seal and Test
- Common Mistakes & Troubleshooting
- Frequently Asked Questions About jon boat outrigger installation steps
- Final Thoughts
Before You Start: Tools, Gear & Preparation
| Item / Tool | Purpose | Optional / Required |
|---|---|---|
| Measuring tape | Find exact spots for brackets | Required |
| Marker or pencil | Mark drill points | Required |
| Drill with metal bits | Make pilot holes | Required |
| Wrench set | Tighten bolts and nuts | Required |
| Marine‑grade bolts, nuts, washers | Secure brackets to hull | Required |
| Marine sealant | Prevent water leaks | Required |
| Safety glasses | Protect eyes while drilling | Required |
| Work gloves | Protect hands | Optional |
| Level | Check brackets are even | Optional |
| Helper | Hold parts while you work | Optional |
Safety check: Work on a flat surface. Keep the boat on its trailer or on blocks. Disconnect any battery power if you have electric accessories. Wear glasses and gloves. Keep a fire extinguisher nearby if you use a power drill.
Step 1: Measure and Mark Mounting Points
First, decide where you want the outriggers. Most people place them about one‑third back from the bow. Measure from the bow to that point on each side.
Use the tape to find the spot. Mark it with a pencil. Do the same on the opposite side. Keep the marks level with each other.
Check the marks with a level if you have one. Ask yourself: “Are the marks even?” If not, adjust now.
Captain’s Note: A helper can hold the tape while you mark. This saves time and reduces error.
Step 2: Drill Pilot Holes
Put on your safety glasses. Choose a drill bit slightly smaller than the bolt shaft. Drill straight down at each mark.
Drill slowly to avoid cracking the hull. Stop when you reach the depth needed for the bolt length.
Clear away any shavings. Look at the hole: “Is it clean and round?” If not, re‑drill gently.
Repeat for all four marks (two per side).
Step 3: Attach Brackets to Hull
Place a bracket over each pilot hole. Insert a bolt through the bracket and hole. Add a washer and nut on the inside.
Tighten the nut with a wrench. Do not over‑tighten; you just need a snug fit.
Apply a thin bead of marine sealant around the bolt where it meets the hull. This stops water from seeping in.
Check each bracket: “Does it sit flat against the hull?” If it tilts, loosen and re‑seat.
Step 4: Mount Outrigger Arms
Slide each outrigger arm into its bracket. Most arms have a pin or bolt that locks them in place.
Insert the locking pin and secure with a cotter pin or clip. Make sure the arm cannot slide out.
Adjust the arm angle if your model allows. A slight outward tilt gives more stability.
Ask: “Does the arm move freely but stay locked?” If it wiggles, tighten the lock.
Step 5: Seal and Test
Run a bead of sealant around the base of each bracket where it meets the hull. Smooth it with a finger or tool.
Let the sealant cure per the product label—usually 24 hours for full strength.
After cure, gently press on each outrigger. The boat should feel solid, not shift.
Take the boat to calm water. Stand on the outrigger and see if it holds. If you feel any give, re‑check the bolts.
Trail Hack: Carry a spare set of nuts and bolts in your dry bag. A quick fix on the water saves a trip back to shore.
Common Mistakes & Troubleshooting
Problem: Bolts keep loosening
Cause: Vibration from waves or motor.
Fix: Use lock nuts or add a drop of thread‑locker to the bolt threads before tightening.
Problem: Water leaks around bolts
Cause: Sealant not applied or cracked.
Fix: Remove the bolt, clean the area, apply fresh sealant, and re‑tighten.
Problem: Outrigger arms sit uneven
Cause: Marks were not level or hull is warped.
Fix: Re‑measure from a known straight line (like the keel). Adjust brackets and re‑drill if needed.
Frequently Asked Questions About jon boat outrigger installation steps
How long do the outriggers last?
With proper sealing and marine‑grade hardware, they can last many years. Check bolts and sealant each season.
Can I install outriggers on a fiberglass jon boat?
Yes. Use the same steps, but drill with a bit made for fiberglass to avoid cracks.
Do I need to remove the outriggers for trailering?
Most designs fold or detach. Follow the maker’s guide; if they bolt on, you can leave them if they fit within the trailer width.
What size bolts should I use?
Check the bracket kit. Usually 1/4‑inch or 5/16‑inch marine‑grade stainless bolts work well.
Is it safe to stand on the outriggers while moving?
No. Only stand on them when the boat is stopped or moving very slowly. Never rely on them for high‑speed stability.
Final Thoughts
You now know the jon boat outrigger installation steps from start to finish. Your boat will be steadier for fishing, hunting, or just relaxing. Take your time, check each bolt, and enjoy the added confidence on the water.
Get out there, try it, and feel the difference. Happy boating!