How to Calculate Required Thickness: 5 Tips

How to Calculate Required Thickness: A Step-by-Step Guide

You need to know how thick a part must be to hold pressure or load. This guide shows you how to calculate required thickness in plain steps. You will learn what data you need, which formula to use, and how to check your answer. The job takes about 20 minutes. No special skill is needed. By the end you can size a pipe, a tank wall, or a boat hull with confidence. Ready to start? Let’s gather the tools first.

Before You Start: Tools, Gear & Preparation

Item / Tool Purpose Optional / Required
Measuring tape Measure diameter or length Required
Caliper or micrometer Check existing thickness Required
Notebook and pen Write down numbers Required
Calculator Do the math Required
Safety gloves Protect hands Optional
Eye protection Shield eyes Optional
Reference chart (ASME or code) Find safe stress values Required

Work on a flat, dry surface. Make sure the part is not under pressure. Keep water and sparks away. If you are on a boat, tie it off so it does not move.

Step 1: Gather the Data

Write down the inside pressure (pressure) the part will see. Use units like psi or bar. If you are not sure, look at the system spec or ask the maker.

Measure the inside diameter (diameter) of the pipe or tank. Use the tape measure. Write the number in inches or millimeters.

Find the allowable stress (safe stress) for the material. This comes from a code chart. For example, carbon steel at 100°F often has a safe stress of 20,000 psi.

Note the joint efficiency (joint factor). A seamless pipe gets 1.0. A welded pipe might be 0.85 or 0.9. Check the code for your joint type.

Decide on a corrosion allowance (extra) if the fluid can rust the wall. A common value is 0.125 inch. Write it down.

Captain’s Note: If you have no chart, a quick web search for “ASME allowable stress carbon steel” will give you a table. Use the value for the temperature you will see.

Step 2: Choose the Formula

For a thin‑walled cylinder the ASME formula is:

t = (P * D) / (2 * S * E - 0.2 * P)

Where:

  • t = required thickness (in)
  • P = internal pressure (psi)
  • D = inside diameter (in)
  • S = allowable stress (psi)
  • E = joint factor (unitless)

If the result is less than 0.125 inch, use the corrosion allowance as the minimum.

Step 3: Plug in the Numbers

Take your notebook. Write the formula again. Replace each letter with the value you gathered.

Example: Pressure = 150 psi, Diameter = 10 inches, Safe stress = 20,000 psi, Joint factor = 0.9.

The formula becomes:

t = (150 * 10) / (2 * 20000 * 0.9 - 0.2 * 150)

Step 4: Do the Math

First multiply the top: 150 * 10 = 1500.

Now the bottom: 2 * 20000 * 0.9 = 36000.

Then 0.2 * 150 = 30.

Subtract: 36000 – 30 = 35970.

Divide: 1500 / 35970 = 0.0417 inch.

This is the thickness needed to hold the pressure.

Step 5: Add Corrosion Allowance

Take the corrosion allowance you wrote down. If you chose 0.125 inch, add it to the result.

0.0417 + 0.125 = 0.1667 inch.

Now the wall must be at least 0.167 inch thick to last.

Step 6: Round Up to a Standard Size

Check a pipe or plate thickness chart. Pick the next size that is equal to or greater than your calculated value.

In our example, 0.167 inch rounds up to 0.188 inch (3/16 inch) or 0.250 inch (1/4 inch) depending on what is stocked.

Write the final size on your drawing or order sheet.

Captain’s Note: Always round up, never down. A little extra thickness costs little but adds a lot of safety.

Common Mistakes & Troubleshooting

Problem: The calculated thickness is too thin.

Cause: You used the wrong pressure value (maybe gauge vs absolute).

Quick Fix: Confirm the pressure unit. If the spec gives gauge pressure, use that number directly in the formula.

Problem: The result seems huge (over 1 inch).

Cause: You may have mixed units (e.g., pressure in bar but diameter in inches).

Quick Fix: Convert everything to the same system. Use psi and inches, or Pa and meters, then redo the math.

Problem: You forget the joint factor.

Cause: Assuming seamless when the part is welded.

Quick Fix: Look at the weld. If you see a bead, use the factor from the code (often 0.85‑0.9).

Frequently Asked Questions About How to Calculate Required Thickness

What if I need the thickness for a sphere?

Use the sphere formula: t = (P * D) / (4 * S * E). The steps are the same; just change the divisor from 2 to 4.

Can I use this method for a flat plate?

Yes, but a different formula applies: t = sqrt( (P * D^2) / (k * S) ), where k depends on edge support. Check a plate‑bending chart for k.

How often should I re‑check the thickness?

Check at each major service interval or after any impact, repair, or change in operating pressure.

Do I need to consider temperature?

Yes. Allowable stress drops as temperature rises. Use the chart value for the max temperature the part will see.

What if I have no calculator?

You can do the math by hand with long division, or use a phone calculator app. The steps stay the same.

Final Thoughts

You now know how to calculate required thickness for pipes, tanks, and hulls. The process is simple: get data, plug into the formula, add corrosion, and round up. Use the steps each time you size a new part or check an old one. Stay safe, double‑check your numbers, and enjoy the confidence that comes from a job done right.

Get out there, measure, calculate, and build something that lasts.

Leave a Comment