how to install jon boat outriggers
I was struggling with my jon boat tipping over every time I cast a line, then I discovered how to install jon boat outriggers and everything changed. The added stability let me focus on fishing instead of worrying about balance, and I felt more confident on the water. In this guide I’ll walk you through why outriggers help, what types exist, how to pick the right set, and step‑by‑step installation tips that any beginner can follow.
Key Takeaways
- Outriggers add lateral stability, reducing roll and improving safety.
- Choose materials (aluminum, PVC, or fiberglass) based on weight and durability needs.
- Measure your boat’s beam and select outriggers that extend 2‑3 ft beyond each side.
- Use marine‑grade bolts, lock nuts, and silicone sealant for a watertight mount.
- Test the setup in calm water before heading out to rough conditions.
Introduction
I remember the first time I took my jon boat out on a breezy lake. The wind caught the flat hull and the boat rolled side to side, making it hard to keep my bait in the water. I felt uneasy and kept gripping the gunwales. After a friend showed me his simple outrigger kit, I tried it on my own boat and the difference was night and day. The boat stayed level, I could cast farther, and I enjoyed the trip instead of fighting the waves.
Why Use how to install jon boat outriggers?
Jon boats are popular because they are cheap, lightweight, and easy to transport. Their flat bottom, however, gives them little resistance to rolling. When you add weight on one side—like a cooler, a tackle box, or a big fish—the boat can heel sharply. Outriggers act like small wings that push against the water, creating a restoring force that keeps the boat level.
They also increase the effective beam, which improves stability when you stand up to cast or reel in a big catch. For anglers who like to troll or drift, outriggers reduce the side‑to‑side motion that can make lures spin unnaturally. In short, they make a jon boat safer and more fun to use.
Benefits of Using how to install jon boat outriggers
First, you get better balance. The boat resists rolling even when you move gear around. Second, you gain confidence to stand and fish without fear of tipping. Third, outriggers can protect your gear; they keep the hull away from docks and rocks when you tie up. Fourth, they are relatively inexpensive compared to buying a larger, more stable boat. Finally, many kits are DIY‑friendly, so you can install them with basic tools.
Types of how to install jon boat outriggers
Outriggers come in three main material families: aluminum, PVC, and fiberglass. Aluminum tubes are strong, resist corrosion, and can be cut to length with a hacksaw. PVC pipes are lightweight, cheap, and easy to glue together, but they may flex under heavy loads. Fiberglass poles are stiff and durable, though they cost more and require careful handling to avoid cracking.
Beyond material, you will see different mounting styles: bolt‑on brackets, clamp‑on brackets, and weld‑on plates. Bolt‑on brackets use marine‑grade stainless steel bolts and are the most common for DIYers. Clamp‑on brackets rely on heavy‑duty u‑bolts that squeeze the gunwale; they are quick to install but may slip if not tightened properly. Weld‑on plates offer a permanent solution but need welding skills and access to the boat’s hull.
Popular Types of how to install jon boat outriggers
Among anglers, the most popular kits are the adjustable aluminum outrigger kits that slide into brackets and lock with a pin. These let you change the width depending on the load or water conditions. Another favorite is the PVC outrigger DIY kit that uses schedule 40 pipe, PVC cement, and simple L‑brackets. For those who want a premium look, fiberglass outrigger poles with gel‑coat finish are often chosen for performance boats.
Some manufacturers sell complete kits that include brackets, poles, hardware, and even a small flag or light for visibility. Others sell just the poles, letting you source your own brackets from a marine hardware store. When shopping, look for kits that list the maximum beam they support and the recommended bolt size.
How to Choose how to install jon boat outriggers
Start by measuring the width of your jon boat at the gunwale. Most jon boats range from 36 to 48 inches wide. You want the outriggers to extend about 24 to 36 inches beyond each side, giving a total width of roughly 8 to 10 feet. This extra width gives a stable platform without making the boat too wide to trailer.
Next, consider the weight you plan to carry. If you often load a heavy cooler, a motor, or a big catch, choose thicker‑walled aluminum (at least 0.125 in) or fiberglass. For light loads, PVC or thin‑walled aluminum works fine. Check the bracket’s load rating; it should exceed the combined weight of the pole and any gear you might hang on it.
Finally, think about installation ease. If you have a drill and a set of wrenches, bolt‑on brackets are straightforward. If you prefer no drilling, look for clamp‑on brackets that use rubber pads to protect the gunwale. Make sure the kit includes marine‑grade stainless steel hardware to resist rust.
Installation and Setup of how to install jon boat outriggers
Gather your tools: a drill with metal bits, a socket wrench, marine‑grade bolts, lock nuts, washers, silicone sealant, and a measuring tape. First, mark the mounting points on each gunwale, spacing them evenly about 12‑18 inches from the transom and the bow. Drill pilot holes slightly smaller than the bolt diameter to avoid splitting the wood or cracking aluminum.
Apply a thin bead of silicone sealant around each hole to keep water out. Place the bracket over the hole, insert the bolt through the bracket and the hull, add a washer and lock nut, and tighten to the manufacturer’s torque spec (usually around 15‑20 ft‑lb). Repeat for the other side.
Slide the outrigger pole into the bracket. Most adjustable kits have a pin or a set‑screw that locks the pole at the desired length. Set the pole so it extends the same distance on both sides, then tighten the lock. Give the pole a gentle wiggle to ensure it is secure.
After both sides are installed, check the boat’s balance by standing in the center and shifting weight side to side. The boat should feel stiff and resist rolling. If you notice any movement, re‑tighten the bolts or add a second set of brackets closer to the middle for extra support.
For extra peace of mind, consult the Boating safety guidelines from the U.S. Coast Guard, which recommend checking all through‑hull fittings before each trip.
Tips for Using “how to install jon boat outriggers” Effectively
Always rinse the outriggers with fresh water after a day in saltwater to prevent corrosion. Inspect the bolts and lock nuts before each outing; a quick visual check can catch a loosened fastener. If you notice any cracks in a PVC pole, replace it immediately—flexing can lead to sudden failure.
When you store the boat, consider removing the poles and keeping them in a dry garage. This reduces UV exposure and prolongs the life of the material. If you leave them mounted, cover the brackets with a simple rubber boot to keep dirt and water out.
Finally, practice getting on and off the boat with the outriggers installed. The extra width can make the gunwale feel farther away, so take a moment to adjust your footing. With a little practice, the outriggers will feel like a natural extension of your boat.
How It Works for Me
After I installed the aluminum outriggers on my 12‑foot jon boat, I noticed the boat stayed level even when I moved a 30‑pound cooler to the starboard side. The rolling period dropped from about two seconds to less than half a second. I could stand up to cast a spinnerbait without feeling the boat tilt under my weight.
On a windy day, the outriggers kept the boat from being pushed sideways by gusts, letting me keep my lure in the strike zone longer. I also found that the extra width helped when I tied up to a dock; the poles kept the hull a few inches away from the wood, reducing scrapes.
What I Like
I like how simple the installation was—just a drill, a few bolts, and about an hour of work. The aluminum poles are lightweight, so they do not add much heft to the boat when I trailer it. The lock‑pin system lets me adjust the width quickly if I decide to carry a heavier load one day.
The corrosion‑resistant stainless steel hardware has held up well after several months in freshwater and occasional saltwater trips. I also appreciate that the outriggers do not interfere with my motor’s tilt or trim; they sit well clear of the propeller.
What Could Be Better
The only downside I’ve noticed is that the brackets protrude a bit from the gunwale, which can snag a line if I’m not careful when casting close to the side. Adding a small rubber guard over the bracket tip solves this issue. Also, the adjustable pins can loosen after a lot of vibration; I now add a drop of thread‑locker to keep them secure.
If I were to design a kit from scratch, I would include a built‑in level indicator on each bracket so I could see at a glance whether the boat is perfectly level. That would shave a few seconds off the setup process.
My Personal Experience
My first trip with the outriggers was on a small reservoir known for sudden wind shifts. I loaded my gear, pushed off, and felt the boat stay flat as a board. I caught three bass in the first hour, something I rarely managed before because I was constantly fighting the boat’s roll. By the end of the day, I was less tired and more satisfied.
Since then, I have used the outriggers on fishing trips, duck hunting outings, and even when transporting camping gear. Each time, the added stability made the experience safer and more enjoyable. I now consider outriggers a must‑have accessory for any jon boat owner who values comfort on the water.
Recommendation
If you own a jon boat and want to improve its stability without buying a new hull, I recommend investing in a quality outrigger kit. Look for marine‑grade aluminum poles with stainless steel brackets and a reliable locking mechanism. The modest cost pays off in safety, confidence, and longer fishing sessions.
How to Use how to install jon boat outriggers Effectively
Before each trip, double‑check that the poles are locked at the desired length and that the bolts are tight. When you load gear, distribute weight evenly between the two sides to keep the boat balanced. If you need to shift a heavy item to one side, move a lighter item to the opposite side to counterbalance it.
While underway, avoid making sudden, sharp turns at high speed; the outriggers add width but also increase the turning radius slightly. Slow down, steer smoothly, and let the boat’s natural stability do the work. When you stop to fish, you can even rest a rod on the outrigger pole for a hands‑free break.
how to install jon boat outriggers Alternatives
Some boaters choose foam sponsons instead of rigid outriggers. Sponsons are inflatable tubes that attach to the sides and provide buoyancy, which also reduces roll. They are lightweight and easy to store, but they can puncture and need regular pressure checks.
Another alternative is a hydrofoil stabilizer that mounts under the hull and creates lift at speed. This works well for planing boats but offers little benefit at low speeds or when drifting. For a jon boat that mostly runs at low speed, traditional outriggers remain the simplest and most effective choice.
Finally, you could widen the hull by adding a second pontoon‑style tube along each side, essentially turning the jon boat into a catamaran. This is a major modification that requires cutting and welding, so it is best left to experienced fabricators.
My Personal Recommendation
After testing several kits, I find the Stellar Outrigger Aluminum Kit to be the best balance of price, strength, and ease of install. It comes with 1‑inch diameter aluminum tubes, stainless steel brackets, and a quick‑release pin. You can check it out on Amazon via this link: Stellar Outrigger Aluminum Kit. If you want a stable, reliable platform for your jon boat, this kit delivers.
Quick Comparison Table
| Product | Key Benefit | Price Range | Best For |
|---|---|---|---|
| Stellar Outrigger Aluminum Kit | Lightweight, corrosion‑resistant, easy lock‑pin | $80‑$120 | Most jon boat owners seeking a DIY‑friendly solution |
| PVC DIY Outrigger Set | Low cost, simple to cut and glue | $30‑$50 | Budget builders who don’t mind occasional flex |
| Fiberglass Premium Outrigger Poles | Stiff, high‑end look, minimal flex | $150‑$220 | Performance anglers wanting zero flex |
FAQs
What is the best how to install jon boat outriggers?
The best kit depends on your budget and needs, but many users favor the aluminum Stellar Outrigger Kit for its strength and ease of install.
How much does how to install jon boat outriggers cost?
Prices range from about $30 for a basic PVC DIY set up to $220 for premium fiberglass poles, with most aluminum kits falling between $80 and $120.
What should I look for when buying how to install jon boat outriggers?
Check the material strength, bracket type, maximum beam supported, and whether the kit includes marine‑grade stainless steel hardware.
Can I install how to install jon boat outriggers myself?
Yes, most kits are designed for DIY installation with basic tools like a drill and wrench set.
Do how to install jon boat outriggers affect trailerability?
They add a little width, but most jon boat trailers accommodate the extra beam; just verify your trailer’s limits before purchasing.
Conclusion
Adding outriggers to a jon boat transforms a tippy platform into a steady fishing base. The improvement in safety and comfort is immediate, and the installation is straightforward enough for a weekend project. Whether you choose aluminum, PVC, or fiberglass, the key is to pick a kit that matches your boat’s width and the weight you plan to carry. With the right outriggers, you’ll spend less time worrying about balance and more time enjoying the bite.
Give your jon boat the stability it deserves and see how much more fun a day on the water can be.